Environmental science

NV 3001 – Global Learning (GL) Assignment

This assignment provides a brief background on materials use and waste management. There are

two topics provided:

Topic 1: Endangered elements

Topic 2: Persistent waste materials in the environment (e.g., plastics)

The GL assignment should be submitted via Canvas before the last class of the semester

(Thursday June 13, 2019).


Select only one of the topics and discuss the issue and develop an overview of the problem as

described in the Topic below. Your report should address the points as indicated, estimated of

quantities, materials and other relevant information. Please limit your report to 2-4 pages

(appendices are OK) including figures, tables, calculations, references.

Extra credit: I have provided a paper to read: “From electronic consumer products to e-wastes:

Global outlook, waste quantities, recycling challenges”

Provide a brief discussion (1 page) on the global cross boundary transport of e-wastes.


There has been significant technological advancements since 1950s. Technology adoption rates

and product replacement cycles create challenges for materials supply and management of

discarded products.

Fig. 1. Major advancements since 1990.

Fig. 2. Technology penetration.

Fig. 3. Product marketing and consumer purchase cycles. Note that disposal is not a main

consumer issue.

Fig. 4. World Population

Fig. 5. Most densely populated regions in the World.

Fig. 6. Water scarcity in the World.

Fig. 6. Growth of World population and the history of technology.

Topic 1: Endangered elements

With rapid growth in innovation and technology development over the past several decades, an

increasing number of elements in the periodic table are now used in advanced consumer products

to perform specialized functions. At the same time, with the decreasing cost and increasing

availability of the consumer products and their short use cycles; there has been increasing

concerns regarding the availability of some of the elements in the future. The concerns for supply

of materials and necessary elements include:

 projected production quantities

 available markets and projected market potential for products

 changes in production or in available ore deposits in different countries

 geopolitically concentrated production of materials

 minimal or lack of end-of-life recycling efforts

The following periodic table has been developed by the American Chemical Society to bring

awareness for the rate of utilization of some elements which are likely to be available in limited


Select one of the endangered elements and discuss:

a. where it is produced b. where it is used c. production rate and consumption rate d. provide preliminary calculations for people using and discarding a specific type of

products where these materials are used

Topic 2: Persistent waste materials in the environment (e.g., plastics)

Decomposition characteristics of plastics in the environment depends on both the conditions in

the environment and the characteristics of the polymeric material. Since majority of the plastics

present in MSW are sensitive to photo oxidation, they can remain stable for longer times in the

landfill in comparison to their transformation behavior when they are exposed to sunlight (i.e.,

floating on the sea surface). A wide variety of chemical additives are incorporated into the

plastics. Some additives are designed to stabilize the polymer and make it more resistant for

degradation. For example, anti-oxidants and stabilizers used as additives inhibit the degradation

of the polymer, while pro-oxidant additives make the plastics more sensitive towards

degradation. Presence of starch increases biodegradability of plastics; however, biodegradation

of starch will not work without a pro-oxidant. The additives used in plastics are usually not

covalently bonded to the polymer. Therefore, they can leach out from the plastic material as it

degrades. Thus degradation rates of the plastics (even those with added starch) depends strongly

on the type and amount of additives used. The half-life of most plastics is over 100 years in

landfills or the environment.

PP: polypropylene, PS:polystyrene, PET: polyethylene terephthalate, LDPE: lowdensity polyethylene, HDPE: high

density polyethylene PVC: polyvinyl chloride

Select one type of plastic (PP: polypropylene, PS:polystyrene, PET: polyethylene terephthalate,

LDPE: lowdensity polyethylene, HDPE: high density polyethylene PVC: polyvinyl chloride) and


a. where it is used b. how much is used and discarded c. provide preliminary calculations for use and discarding rates of the specific type of


Order now and get 10% discount on all orders above $50 now!!The professional are ready and willing handle your assignment.